Closing daily for lunch from 1245 to 130pm and now open Saturday's from 8am to 1230pm
Product quantities are updated every 15 minutes. If in doubt please call to ensure stock is available before travelling 028 9083 2312

Felt Accessories



£6.65 £7.98 (inc. VAT)
Stock Status: Sold Out
Low stock - Please call us for details on (028) 9083 2312. You can still order and we will deliver as soon at the product arrives into stock

EVERCRYL EMERGENCY ROOF REPAIR is a resin based, fibre re-enforced roof repair compound which is effective on all common roofing surfaces and types, giving an instant roof repair even in the wet and on wet surfaces. May also be applied in frosty conditions down to 5`C. EVERCRYL EMERGENCY ROOF REPAIR is instantly waterproof when applied, so there is no fear of wash off, so emergency leaks can be tackled immediately as there is no need to wait for the rain to stop. EVERCRYL EMERGENCY ROOF REPAIR is cartridge applied and dries to a flexible membrane which resists algae and fungal growth. Because of the high level of fibre re-enforcement, EVERCRYL EMERGENCY ROOF REPAIR will bridge small cracks and holes up to 10mm, requires only a one application to give instant and total water protection, even in areas subject to ponding. EVERCRYL EMERGENCY ROOF REPAIR requires no primer on sound non-porous surfaces.

May be applied in damp and wet conditions.
Formulated from lightfast acrylic polymers to withstand sunlight for longer periods than traditional bitumen
Fibre re-enforced to bridge small cracks.
Primerless adhesion to most bituminous and non porous surfaces.

Areas For Use
General sealing, maintenance, repair and waterproofing of most common roofs in wet or dry conditions for use on concrete, fibre/cement, roofing felt, mastic asphalt, existing bituminous roof coatings, rigid uPVC corrugated iron, metals, slates, brickwork, tiles, lead, copper and zinc.
Waterproofing guttering (plastic and metal), downpipes, gullys, flashings, upstands, vents and leadwork.


Do not use in areas where subsequent solvent or oil contact is likely.. Avoid inhalation of vapours. Do not use on Styrofoam or PVC foil. As the manufacturer cannot know all the uses its products may be put to, it is the users responsibility to determine suitability for use. If in doubt, contact technical services department for advice.

Surface Preparation
No roof-coating product can be expected to repair an existing roof that is not structurally sound and stable. Before using a surface coating the roof structure should be inspected and, if necessary, put in order. All cracked, broken, slipped or missing slates, tiles, sheets or other forms of covering should be replaced or re-fixed and cracks in felt or asphalt filled. (Safety Recommendation: do not coat roof lights, windows, glass or translucent sheets. These will constitute a hidden hazard if disguised.

Preparation of the surface is of great importance and will influence the degree of adhesion and life of the renovation. All roof surfaces to be coated should be sound, stable, clean, i.e. free from loose debris, dirt, dust and grease. All traces of algae and fungi growth should be removed using a stiff-bristled brush. Where algae and fungi have been present, remove them completely and treat the surface with EVERBUILD MOSS AND MOULD REMOVER to kill any remaining spores, thereby discouraging the return of the growths.

Make good any holes or loose felt/slates/tiles etc. Fill holes/imperfections with BLACK JACK BITUMEN MASTIC. Stick down loose felt etc with BLACK JACK ROOF FELT ADHESIVE. Blisters in roofing felt must be cut, dried, re-bonded and sealed. New metal surfaces must be degreased with a suitable solvent. Remove all rust or treat rusty surfaces with a rust inhibitive primer (eg zinc phosphate based). All non- bituminous, porous or friable surfaces must be primed with BLACK JACK BITUMEN AND FLASHING PRIMER allowing primer to dry thoroughly before use.

Wear gloves and suitable face/eye protection. Flammable product - eliminate all sources of ignition. Cut the tip of the cartridge, taking care not to damage the thread apply special nozzle. In extreme cases a second application may be made 2-3 days after initial application.
  • Product Code:
Not yet reviewed
Write an online review and share your thoughts with other shoppers!
Be the first to review this product